Product Description
These are Revolver Supply Premium moon clips. They are designed to work in the Taurus 5 shot Model 905 revolvers chambered in 9 MM.
These moon clips are 0.020" thick, made from Stainless Steel.
You must order this sample pack and test the moon clips in the revolver.
If they fit we'll enable you to see the larger quantity pricing and purchase larger quantities.
**These moon clips will not fit in all Taurus Model 905 revolvers.**
*THIS IS A PACKAGE OF 1**
Product Videos
Custom Field
Product Reviews
25 Reviews Hide Reviews Show Reviews
-
great product
Product. Just as advertised. Will shop with revolver supply again GM- Not all revolvers are machined as well as yours.
-
Not machined well. GM - I disagree read on
I started out laying it on revolver and it laid flat seemed to work well. When I started putting 380's on clip they sled in with no resistance and would fall out if I tilted moon clip. I have carried and fired revolvers with moon rings(clips) for many years and am sorry but this one would not even hold the bullet's in place. I tried more the one brand also. GM- These Moon Clips are made for the 9MM cartridge. The 380 round is much smaller. So that's why they fall out.
-
moon clips
Sorry for last review.I must have messed up on writing it. Sorry, my mistake Tom GM- 1st review 5 stars but didn't like the clips. This review he likes them.
-
Better thn teh facory moon clips
Great product. Had to emory a little but not too bad. So good i ordered the 10 pack. GM These clips work in a bit over half of the guns. Some folks even cleaned up the cylinder on a lathe. That's the root of the problem.
-
second set, no fit
This is the second set of two I've purchased for the Taurus 905, and like the initial pair, these too require filing to get them to fit. While it's easy enough to put these in a vise and take off a mil or two (5 times per clip). they still ought to be made to fit the revolver they are made for. for the fix details, see the earlier review GM- Yours was close. Others fit as is and others won't fit at all. Taurus can't make a consistent cylinder.
-
Doesn't fit until center hole enlarged
Since this is sold as a clip for the Taurus 5 shot 9mm 905, I ws surprised that I couldn't close the cylinder into the gun because the clip did not fit over the center machining in it. Had to file material off the inside of each holder slot to make it fit. Once reworked, the clip retained cartridges better than the factory-supplied ones. If this is what is sold as a clip to fit the Taurus 905, I suspect the maker ought to pay another visit to the drawing board. For those of you willing to dress the center hole of these clips, I suggest a vice and a 3-corner fine file. Lots cheaper than a Dremel tool. GM This is exactly why we offer 2 with free shipping for testing.
-
Works great
They are just what we were hoping for, work great.
-
Needed A Little Tweeking
The moon clips didn't fit until I removed a small amount of material with a needle file. I can see why they're hard to fit because the center hub on my revolver is poorly machined and hasn't been deburred properly. I was impressed with the cartridge retention and had to make up a tool to remove the spent cases. There's no way a cartridge is going to come loose if you throw a clip in your pocket. GM- That's exactly what we see and why we created these 2 packs. I don't want to make the moon clip opening larger. It would weaken the clip. Thanks
-
We can make this work
I can use all 4 of my "samples" (yes I bought two packs). I would say all 4 are usable but the center hole needs to be dressed. If I can't find a suitable Dremmel tool as I don't own one, I might try a pencil with an emery cloth to make it work smooth. We are only talking a few thousandths. I am wondering if the machine shop could "smooth" a bit more from the center to get closer to 100% fit. I am just glad to get something that will work without breaking the bank. I can press these into place as is, but will smooth out. Thanks for this option!
